03.04.2020
Motor mounting and Coupling (MGK), What is the tightening torque of the clamping ring hub tensioning screws of the couplings? ( Download PDF operating and assembly instructions Rotex GS ) ,
10.08.2023
ball-/trapezoidal-threaded nut, fixed-/movable bearing, spindle support Steel belts and rollers of our roller guide Guide rail and guiding carriage of our ball guiding rail Sliding guide/ supporting sliding guide [...] miscibility of the greases. Here, the base oils and the thickener systems should match each other in order to exclude negative effects. What is HSB’s standard grease and what is its miscibility? Klüberplex BE 31-102 [...] ) What are the re-lubrication intervals and -quantities of the ball screw drives? The re-lubrication intervals of the ball screw drives depend on the slope and the spindle-diameter. The initial lubrication
13.09.2021
GmbH gives recommendations for the drive motors (and possibly gearboxes). These are to be checked by the supplier when an order is placed. The motor and gearbox design at HSB is based on our many years [...] in this area. Maximum load, average load, dynamic parameters and duty cycle are taken into account. This occasionally means that motors and / or gears can absorb significantly more power than the linear [...] programming do not lead to serious damage to the linear module and / or the add-on parts. The in our linear modules built in end position dampers and stop buffers serve to protect the unit at low speeds (co
24.05.2023
(ATEX) ) Our Beta and Delta linear units with rail guides and roller guides can be used in explosive range. They can serve in the equipment group II, category 2 (zone 1 gas, zone 21 dust) and category 3 (zone [...] download: design data for linear units ATEX and ESD declarations of conformity supplement to our assembly and maintenance instructions Our linear units HSB-beta ® and HSB-delta ® (except for the sliding guides) [...] installed components like guide and screw gear cannot be guaranteed. All HSB-linear units with rail guide are designed for grease lubrication. HSB recommends single-point and multi-point grease lubrication
22.02.2021
pitch of 5 mm and 10 mm è ca. 0,02 mm 1 Single nut with minimal play and a pitch of 20 mm and 25 mm è ca. 0,02 to 0,04 mm Single nut with minimal play and a pitch of 40 mm and 50 mm è ca. 0,03 to 0,08 [...] mm and 10 mm è ca. 0,04 to 0,06 mm Single nut with a pitch of 20 mm and 25 mm è ca. 0,06 to 0,08 mm Single nut with a pitch of 40 mm and 50 mm è ca. 0,08 to 0,15 mm Single nut with minimal play and a pitch [...] of the unsupported spindle and its rotation speed The respective values can be extracted from the speed diagram shown in the catalogue. They are also indicated in the offer and order confirmation. On what
01.03.2023
band The standard cover strips come in the colors blue and black. At high temperatures (>+40°C), the black cover strips are more temperature-stable and expand less linearly. Download PDF PAS-100-cover band [...] well as high temperature applications (up to +120°C). It can even stand more extreme temperatures and is e.g. resistant to weld spatters. (Download PDF Valflon cover band) ,
03.04.2020
extracting turned parts out of machines and placing them in boxes E.g.: package handling; extracting packages out of packaging machines and stacking them onto palettes And a detailed description of the work [...] cycle/ shift operation Desired lifetime Note: The particulars for speed and acceleration may be waived, if the driving profile and the number of cycles are specified together with the downtime. 3. Installation [...] pulley What has to be taken into account when laying out linear units? Design criteria for linear units and systems. To make a reasonable specification of units possible, following aspects have to be clarified
03.04.2020
one of the hexagonal surfaces. (Download PDF GX clamping elements KTR 131) What are the coupling’s and the joint shaft´s moments of inertia? See the file attached for the corresponding data. (Download PDF
07.02.2022
inductive proximity switches? The switching distance is the distance between an approaching metal part and the active surface where the signal change is released. The switching distance depends on: Approach