These Safety Regulations are user hints only, and m ay not be complete! Safety Sign Danger! Danger of injury to personnel and damage to machines. Installation and Operational Instructions for ROBA®-linearstop [...] safety and / or installation conditions are ignored. User-implemented protective measures Cover all moving parts to protect against seizure. To prevent injury or damage, only professionals and specialists [...] (Fig. 1) to the compressed air connection and pressurize the brake with operating pressure, see Table 1 (release brake). 2) Push the brake onto the brake rod and bring it up to contact to the mounting flange

Dateityp: application/pdf
Verlinkt bei:

mounting side C and D AZ6-GX/C = Drive shaft short, mounting side D and Drive shaft long, without feather key groove, mounting side C AZ6-GX/D = Drive shaft short, mounting side C and Drive shaft long [...] description) Further accessories (separate position) MGK = Motor mounting and coupling (according to dimension sheet) Limit switch mounting and lubrication points see page Z1 Ordering code for Toothed Belt Drive [...] ARH = Lifting axis (Vertikal) ARS = Standard (Horizontal) Drive specifications Width of toothed belt and tooth pitch Stroke per revolution Stroke Total length Accessories AZ1 = Drive shaft short, mounting

Dateityp: application/pdf
Verlinkt bei:

pinion: 10.0 Nm Rack and pinion: Module 3 helical Drive pinion: Module 3, 20 teeth Stroke per revolution: 200 mm DynaGear D115 Ratios: 5 / 10 / 15 Servo-High-performance-gear:Forces and Moments (longer on [...] on request) with rack-and-pinion drive module 3 (helical) and double linear guide (AZSS) AZSS-D115 Forces Dynamic [N] 5000-7500 ** 40000 40000 Moments Dynamic [Nm] 13000 25000 25000 Fx FY FZ MX MY MZ Variants [...] Variants for gearbox mounting see catalouge page G29. * inclusive gear and two mounting plates ** depending on gear ratio (see table to right) D115 Dynamic [N] i = 5:1 7500 i = 10:1 i = 15:1 5000 Load FX

Dateityp: application/pdf
Verlinkt bei:

see catalouge page G29. * inclusive gear and two mounting plates ** depending on gear ratio (see table to right) with rack-and-pinion drive module 4 (helical) and double linear guide (AZSS) * * * Drill pattern [...] pinion: 12.0 Nm Rack and pinion: Module 4 helical Drive pinion: Module 4, 21 teeth Stroke per revolution: 280 mm Servo-high-performance-gear: DynaGear D130 Ratios: 5 / 10 / 15Forces and Moments AZSS-D130 [...] pattern of the carriage plate is individually tested and manufactured. Individual lubrication of the guide carriages with prepared hose connections Ø6. Specify the desired RAL color, because steel version

Dateityp: application/pdf
Verlinkt bei:

then heat treated and polished. HSB ball screw nuts are first machined in the soft condition, then heat treated and finish machined in a modern hard turning process. Both spindles and nuts are finished [...] right-hand max. length: 5600 mm Material: 1.1213 (Cf 53) Bearing track induction hardened and polished Spindle end and spindle core are soft Straightness: L < 500 mm: 0.05 mm/m L = 500 – 1000 mm: 0.08 mm/m [...] is 45° (±5°). Speeds The generally permitted speed limit is 3000 rpm. On request, for certain sizes and installation situations, speeds up to 4500 rpm are permissible. The speed limits are the maximum speeds

Dateityp: application/pdf
Verlinkt bei:

Moments (longer on request) with rack-and-pinion drive module 2 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) GDHE-D55 Forces Dynamic [N] [...] element: Rack and pinion: Module 2 helical Drive pinion: Module 2, 18 teeth Stroke per revolution: 2 x 120 mm DynaGear D55 Ratios: 5 / 10 / 15 Toothed belt 32 AT10 Servo-High-performance-gear:Forces and Moments

Dateityp: application/pdf
Verlinkt bei:

Moments (longer on request) with rack-and-pinion drive module 2 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) Release: 18.05.2020 Page GDHE2 [...] Rack and pinion: Module 2 helical Drive pinion: Module 2, 30 teeth Stroke per revolution: 2 x 200 mm DynaGear D75 Ratios: 5 / 10 / 15 Toothed belt 40 AT10-E Servo-High-performance-gear: Forces and Moments

Dateityp: application/pdf
Verlinkt bei:

Moments (longer on request) with rack-and-pinion drive module 3 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) Release: 14.07.2020 Page GDHE4 [...] Rack and pinion: Module 3 helical Drive pinion: Module 3, 20 teeth Stroke per revolution: 2 x 200 mm DynaGear D115 Ratios: 5 / 10 / 15 Toothed belt 40 AT10 Servo-High-performance-gear: Forces and Moments

Dateityp: application/pdf
Verlinkt bei:

Moments (longer on request) with rack-and-pinion drive module 4 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) Release: 18.05.2020 Page GDHE6 [...] Rack and pinion: Module 4 helical Drive pinion: Module 4, 21 teeth Stroke per revolution: 2 x 280 mm DynaGear D130 Ratios: 5 / 10 / 15 Toothed belt 75 ATS15 Servo-High-performance-gear: Forces and Moments

Dateityp: application/pdf
Verlinkt bei:

mounting side C and D AZ6-GX/C = Drive shaft short, mounting side D and Drive shaft long, without feather key groove, mounting side C AZ6-GX/D = Drive shaft short, mounting side C and Drive shaft long [...] (Horizontal) SD = Standard double (Horizontal) H = Lifting axis (Vertical) Drive specifications Width and type of toothed belt Stroke per revolution Stroke Total length Accessories AZ1 = Drive shaft short [...] arrangements for drive shaft, see page Z1 AZx-S = Drive shaft special (x=1 side C, x=2 side D, x=6 side C and D) EO2 / EO10 = Inductive limit switch NC with 2 m / 10 m cable fitted ES2 / ES10 = Inductive limit

Dateityp: application/pdf
Verlinkt bei: