03.02.2021
Moments (longer on request) with rack-and-pinion drive module 2 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) Release: 18.05.2020 Page [...] Rack and pinion: Module 2 helical Drive pinion: Modul 2, 30 teeth Stroke per revolution: 2 x 200 mm DynaGear D75 / D90 Ratios: 5 / 10 / 15 Toothed belt 40 AT10 Servo-High-performance-gear: Forces and Moments
Dateityp: application/pdf
Verlinkt bei:
03.02.2021
ormance-gear: Forces and Moments (longer on request) with rack-and-pinion drive module 3 (helical) and double linear guide (AZSS) and toothed belt drive of the moving carriage and double rail guide (ZSS) [...] acceleration: 20 m/s² Repeat accuracy: ±0,10 mm Idle torque at drive pinion: 9.0 Nm Drive element: Rack and pinion: Module 3 helical Drive pinion: Module 3, 20 teeth Stroke per revolution: 2 x 200 mm DynaGear
Dateityp: application/pdf
Verlinkt bei:
08.01.2024
M8 10 16499 20 13 6 M6 RM4 15371 13 8 6 M5 C and D 1 10556 12 10 4 M4 2 10557 16 10 4 M5 RM2 15370 10 6 4 M4 E 4.1 16552 20 13 6 M8 10 16499 20 13 6 M6 C and D 8 14644 12 8 4.5 M5 9 14652 12 8 4.5 M4 12 [...] 16499 20 13 6 M6 C and D 1 10556 12 10 4 M4 2 10557 16 10 4 M5 11 18714 12 10 3.5 M4 RM2 15370 10 6 4 M4 Beta 120 E 4.1 16552 20 13 6 M8 5 10560 20 14 8 M8 10 16499 20 13 6 M6 C and D 1 10556 12 10 4 M4 [...] RM4 15371 13 8 6 M5 C and D 1 10556 12 10 4 M4 RM2 15370 10 6 4 M4 Beta 165(-C) E 6 10561 25 18 8 M10 RM6 15372 18 10 8 M6 Beta 180(-C) E 6 10561 25 18 8 M10 RM6 15372 18 10 8 M6 C and D 3 10558 20 12 5 M6
Dateityp: application/pdf
Verlinkt bei:
28.10.2019
mount the holders first and then the proximity switches. Adjustment Instructions EANHT Holder for proximity switch: NHT þ with depth stop þ holders already mounted: preadjusted and ready for use Adjust [...] cess for selfreinforcing clamping heads (Safety Catchers, Safety Brakes, Safety Locks). Signal 1 and signal 2 must never be present at the same time, except during the switching process. 2 Proximity [...] Adjustment sleeve 4 Locknut 5 Proximity switch Fig. 2: NHT holder with proximity switch 4 Mounting and adjustment 4.1 State as supplied: Holders are mounted The holders are preset to the correct depth.
Dateityp: application/pdf
Verlinkt bei:
28.04.2025
mounting side C and D AZ6-GX/C = Drive shaft short, mounting side D and Drive shaft long without feather key groove, mounting side C AZ6-GX/D = Drive shaft short, mounting side C and Drive shaft long [...] Standard Drive specifications Width and type of toothed belt Stroke per revolution Stroke Total length Cover AK = Cover band (Note: Total length is greater for Beta 80 and Beta 100) Accessories AZ1 = Drive [...] Special (add specification description) Further accessories (separate position) MGK = Motor mounting and coupling (according to dimension sheet) URT = Deflection belt drive (according to dimension sheet)
Dateityp: application/pdf
Verlinkt bei:
13.06.2025
for Portal Linear Drive Sliding blocks (NS) and mounting brackets (BL) Sliding blocks (NS) and mounting brackets (BL) Profile Dimensions, Sliding Blocks (NS) and Mounting Brackets (BL) Profile Dimensions [...] SA by 120 mm and with 6 SA by 220 mm 0 50 0 10 00 15 00 20 00 25 00 30 00 35 00 40 00 45 00 50 00 55 00 0 500 1000 1500 2000 2500 3000 with ball screw (KGT) and rail guide (SSF) Forces and Moments SSF Forces [...] +Mz +Fz +Fx * for KGT 3240 and 3260: 8000 N 0,00 1,00 2,00 3,00 4,00 5,00 4500 4750 5000 5250 5500 5750 6000 with toothed belt drive and double linear guide (ZSS) Forces and moments d) Maximum value (see
Dateityp: application/pdf
Verlinkt bei:
28.09.2016
04.04.2012 HSB-Beta® ORS-OSS Technical data (e.g. forces and moments, lubrication etc.) and other information see „Assembly And Maintenance Manual” of corresponding powered linear unit of the same dimension
Dateityp: application/pdf
Verlinkt bei:
13.06.2025
mm and 10 mm approx. 0.04 to 0.06 mm pitch 20 mm and 25 mm approx. 0.06 to 0.08 mm pitch 40 mm and larger approx. 0.08 to 0.15 mm S1 = low play pitch 5 mm and 10 mm approx. 0.02 mm pitch 20 mm and 25 mm [...] mm approx. 0.02 to 0.04 mm pitch 40 mm and larger approx. 0.03 to 0.08 mm S0 = free of play no free play, very small pro-load V3 = 3 % pre-load V5 = 5 % pre-load (in relation to the dynamic load rating)
Dateityp: application/pdf
Verlinkt bei:
13.06.2025
bearing grease to DIN 51818. Detailed data on the amounts of grease and lubrication intervals can be found in the “Installation and Maintenance Manual” as well as on the Internet under www.hsb-automation [...] The permissible operating temperature range for ball screws is between 0 °C and +80 °C. A minimum temperature of -20 °C and a maximum temperature of +110 °C are permissible for brief periods. This always [...] important is order that the ball screw achieves its calculated service life, to prevent excessive heating and to guarantee smooth, quiet running. KGT uses the same lubricants as are used for roller bearings. Oil
Dateityp: application/pdf
Verlinkt bei:
27.01.2021
HSB-Beta® Type Right-Left Technical data (e.g. forces and moments, lubrication etc.) and other information can be found in the respective assembly and maintenance manual for the linear units of the same
Dateityp: application/pdf
Verlinkt bei: