are sealed and maintenance-free. The toothed belt is also maintenance-free and must only be replaced if an excess load leads to the breakage or elongation of the elastic area. Excessive dust and contamination [...] is Febis K68 or INTERFLON fin super. Please refer here to our assembly and maintenance instructions. The relubrication interval and the relubrication amount are generally influenced by many factors (e.g [...] contamination on the toothed belt and at the cover band should be regularly removed. For ball screws, relubrication intervals depend on the pitch and the spindle diameter: KGT 12xx to 32xx after approx. 2.5 x

Dateityp: application/pdf
Verlinkt bei:

art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards) [...] legible (in particular the serial number) and always observed. Any damaged or illegible information signs and labels must be replaced. Accident Prevention and Environmental Protection The applicable r [...] guidance of Delta 90 (above) and Delta 200 linear unit A mechanical linear unit converts rotational motion into linear motion and is used to move loads quickly, safely and precisely from one position to

Dateityp: application/pdf
Verlinkt bei:

are sealed and maintenance-free. The toothed belt is also maintenance-free and must only be replaced if an excess load leads to the breakage or elongation of the elastic area. Excessive dust and contamination [...] contamination on the toothed belt and at the cover band should be regularly removed. For ball screws, relubrication intervals depend on the pitch and the spindle diameter: KGT 12xx to 32xx after approx. 2.5 x [...] bellows can be used here. Please refer here to our assembly and maintenance instructions. Note: PRESSOL 12226 (125 cm³) one-hand grease gun with spout and corresponding coupler can be ordered from us. Klüberplex

Dateityp: application/pdf
Verlinkt bei:

devices and covers. You may only assemble, operate and maintain the coupling if you • have carefully read through the operating/assembly instructions and understood them • are technically qualified and specifically [...] source. For gases, vapours and dusts generated the permissible glow and ignition temperatures specified in chapter 10.1 have to be considered and observed. M2 2G 2D No gases and vapours of explosion group [...] (hub type 1.0, 1.1 and 1.2) 24 4.5 Assembly of the clamping hubs (hub types 2.0, 2.1, 2.5, 2.6, 2.8 and 2.9) 25 4.6 Assembly of clamping ring hubs (hub type 6.0 light, 6.0 steel and 6.0) 25 4.7 Disassembly

Dateityp: application/pdf
Verlinkt bei:

until the distance between the flanged disc and the base plate (1) is approx 1 mm, then tighten the clamping set. 3. Attach drive motor to base plate (1) and lightly secure the fastening screws such that [...] g disc (4) in the toothed belt (5) and push onto the motor shaft (with or without clamping set, depending on version) until the distance between the flanged disc and the base plate (1) is also approx. [...] motor mounting/linear unit mounting and the shafts, ensure that the toothed belt is not excessively tensioned. 6. Attach the enclosure lid (6) to the base plate (1) and secure with screws. Linear unit Motor

Dateityp: application/pdf
Verlinkt bei:

extinguishing water and burnt pieces and dispose according to local government regulations. With the above in formation , wh ich corresponds to our current leve l o f knowledge and exper ienc e, we want [...] knowledge and exper ienc e, we want to descr ibe our product w ith regard to any safety requ irements. However, we do not assoc iate th is w ith any property assurances . Exis t ing laws and regu lat ions [...] Stiwen Kunststoffe GmbH +43 5574 72763 office@stiwen.at SAFETY DATA SHEET according to 91/155/EWG and ISO 11014 Material: PAS-100 Ext. Composition: Chemical characterization: Polyamide 12 CAS No.: 25038-54-4

Dateityp: application/pdf
Verlinkt bei:

Delta 110-C-SSS Lubrication of spindle drive (S). Lubrication of guiding carriages 1+2 and 3+4 (F). The spindle drive and guiding carriages must be lubricated through all three funnel grease nipples on either [...] Delta 145-C-SSS Lubrication of spindle drive (S). Lubrication of guiding carriages 1+2 and 3+4 (F). The spindle drive and guiding carriages must be lubricated through all three funnel grease nipples on either [...] Lubrication of spindle drive (S). Lubrication of guiding carriages 1 through 4 (F). The spindle drive and guiding carriages must be lubricated through both funnel grease nipples on either side. F(1-4)S Lubrication

Dateityp: application/pdf
Verlinkt bei:

ingredient and labeling review. Dear Ms. Corinna Gienger: NSF Registration of this product is current when the NSF Registration Mark and Category Code appear on the NSF-approved product label, and the Registered [...] for use in and around food processing areas. Such compounds may be used on food processing equipment as a protective anti-rust film, as a release agent on gaskets or seals of tank closures, and as a lubricant [...] Substances and Nonfood Compounds (2017), which are available upon request by contacting NonFood@nsf.org . The NSF Nonfood Compounds Registration Program is a continuation of the USDA product approval and listing

Dateityp: application/pdf
Verlinkt bei:

ingredient and labeling review. Dear Ms. Corinna Gienger: NSF Registration of this product is current when the NSF Registration Mark and Category Code appear on the NSF-approved product label, and the Registered [...] for use in and around food processing areas. Such compounds may be used on food processing equipment as a protective anti-rust film, as a release agent on gaskets or seals of tank closures, and as a lubricant [...] Substances and Nonfood Compounds (2017), which are available upon request by contacting NonFood@nsf.org . The NSF Nonfood Compounds Registration Program is a continuation of the USDA product approval and listing

Dateityp: application/pdf
Verlinkt bei:

limit switches and end of travel dampers. Installation Cover Any contamination that occurs during installation should be removed using kerosene, oil or benzine. Cold cleaning solvents and paint solvents [...] (large axial space requirement) Our range also includes fully protected and ready-to-install systems: HSB-beta®, HSB-delta® and HSB-alpha® linear guides providing integral guidance within an encapsulated [...] Page TK5 Release: 05.02.2025 Installation The installation of ball screws demands technical knowledge and appropriate measuring equipment. Due to the low friction of a ball screw, alignment errors when turning

Dateityp: application/pdf
Verlinkt bei: