to specify general rules for relubrication intervals for all operating conditions. It is also not easy to provide a constant variable for defining relubrication intervals. For ball bearings, the number [...] product is intended for professional use, not for private use. Intended use also implies that you have read this documentation in full and understood it. General FM 225 A&M instructions for ball screw, rev [...] FM 225 A&M instructions for ball screw, rev.011 1.4 Responsibilities of the operator The product operator is responsible for adhering to appropriate safety measures implemented for the specific purpose of

Dateityp: application/pdf
Verlinkt bei:

Midle = Idle torque ±30 % The data given for forces and moments are the respective maximum values for the single load. The individual values must be reduced for a mixed load or the appearance of several [...] design FM 133 A&M Instr. for Gamma type Z Rev.01 2024-08-26 7 Tightening torques [Nm] for fixing screws Fixing screws M4 M5 M6 M8 M10 M12 The figures given are intended as guides. For shorter insertion depths [...] slight injury or material damage. Note Includes tips for the operation and optimal use of the machine. 1.2 Intended use The linear unit is solely intended for the purpose of manipulating, positioning, transporting

Dateityp: application/pdf
Verlinkt bei:

Maintenance instructions for THK and Rexroth rail guide Maintenance instructions for roller guide Maintenance instructions for ball screw Other maintenance instructions For all guide carriage sizes, the [...] the relubrication interval is approx. 5000 km for the carriage with ball chain or approx. 2000 km for the carriage without (Rexroth without ball chain / standard). It is dependent on several factors, i [...] Under normal operating conditions (dry environment, no dust, etc.), the roller guide is lubricated for life by integrated lubricating felts. The relubrication interval and the relubrication amount are generally

Dateityp: application/pdf
Verlinkt bei:

% (Value given applies for gear ratio i=6) The data given for forces and moments are the respective maximum values for the single load. The individual values must be reduced for a mixed load or the appearance [...] bottom value is for AZSS 2) The value changes if combined with other system parts. Technical Data - Standard design FM 122 AaM Instr. for Gamma type AZ Rev.01 2024-08-26 7 Forces and moments for Gamma linear [...] slight injury or material damage. Note Includes tips for the operation and optimal use of the machine. 1.2 Intended use The linear unit is solely intended for the purpose of manipulating, positioning, transporting

Dateityp: application/pdf
Verlinkt bei:

Tightening torque for M5 screws: 6 Nm Tightening torque for M6 screws: 10 Nm Tightening torque for M8 screws: 24 Nm b) Maximum screw-in depth t = 13,5 mm (for sizes 2 and 6) or 12,5 mm (for size 4) (see Table [...] brake must run freely on the brake rod). The brake is attached using 3x M5 (for size 2) or 3x M6 (for size 4) or 3x M8 (for size 6) screws, strength 8.8 (not included in delivery) (Fig. 1) (Ø F or thread [...] Malfunctions / Breakdowns Declaration of Conformity A conformity evaluation for the applicable EU directives has been carried out for this product. The conformity evaluation is set out in writing in a separate

Dateityp: application/pdf
Verlinkt bei:

Mz Mz shared by 1 roller Fz : Force in Z direction Mx : Moment for longitudinal axis (X) My : Moment for lateral axis (Y) Mz : Moment for vertical axis (Z) Fr : Force on the roller ly : Guiding distance [...] : Force in feed direction Fz : Force in Z direction Mx : Moment for longitudinal axis (X) My : Moment for lateral axis (Y) Mz : Moment for vertical axis (Z) Fs : Force on a carriage lx1 : Guiding distance [...] : Force in feed direction Fz : Force in Z direction Mx : Moment for longitudinal axis (X) My : Moment for lateral axis (Y) Mz : Moment for vertical axis (Z) Fs : Force on a carriage ly : Guiding distance

Dateityp: application/pdf
Verlinkt bei:

data for linear units ATEX and ESD FM 335 ao/24.04.2023 Seite 1 von 1 FM_335_Auslegungsdaten_für_Lineareinheiten_ATEX_und_ESD_EN.docx Rev. 02 ao/20.02.2024 The following designs can be realized for the [...] felts for roller guides internal parts are not coated or anodized no sliding guide no lenghtwise sealing no limit switches no deflection belt drive no spindle support No end position dampers for spindle [...] Ausführung cover band: yes* The installation position must not be overhead or to the side no Only possible for toothed belt axes used in the gas sector * maximum possible total length: Spindle axis = results from

Dateityp: application/pdf
Verlinkt bei:

by 220 mm for 2 SA = 120 for 4 SA = 170 for 6 SA = 220 w ith fe at he r k ey deep 8.5deep 25deep deep 2 SA0 SA 4 SA 8 SA6 SA Mounting elements see page B50 +Fx for 2 SA = 90 for 4 SA = 140 for 6 SA = 190 [...] 34 ∙10-3 kgm²/m Special design: Spindle support with damping ring (extension of total length: 10 mm for every 2 SA) Version with double nut (“MM“)not possible. . Spindle support (SA) Total length [mm] R

Dateityp: application/pdf
Verlinkt bei:

Maintenance instructions for THK and Rexroth rail guide Maintenance instructions for roller guide Maintenance instructions for ball screw Other maintenance instructions For all guide carriage sizes, the [...] the relubrication interval is approx. 5000 km for the carriage with ball chain or approx. 2000 km for the carriage without (Rexroth without ball chain / standard). It is dependent on several factors, i [...] amount are generally influenced by many factors (e.g. speed, temperature, ambient conditions, etc.). For this reason, only reference values have been given here. Relubrication should take place at least every

Dateityp: application/pdf
Verlinkt bei:

Note Includes tips for the operation and optimum use of the unit. 1.2 Intended use The mechanical linear unit is designed for installation into machinery and is solely intended for manipulating, positioning [...] linear unit may be used for industrial applications only. Utilisation of the product for any other purpose would constitute inappropriate use. The manufacturer accepts no liability for any damage resulting [...] operation For safe operation, please take into account the following documentation: • these Operating Instructions for the linear unit, in particular the technical data • the Operating Instructions for the entire

Dateityp: application/pdf
Verlinkt bei: