for the better. Straightness and torsion All aluminium profiles used for the linear devices and the linear tables are extruded profiles. The straightness and torsion of these profiles may deviate as a [...] , load, speed, deceleration and direction of travel may influence the repeat accuracy. Mechanical Linear Drives with Screw Drive For calculating service life, the guide and screw drive load ratings are [...] standard configurations (not double nut or low-backlash single nut) and are measured at a very low speed (≈ 0 min -1). Production and assembly tolerances vary by ± 20 %. The permissible deflection of the

Dateityp: application/pdf
Verlinkt bei:

system) and a drive element (screw or timing belt drive). Depending on its design, the carriage is able to absorb forces and moments in all directions, and is positively connected to the guidance and drive [...] m/s), and for any cleaning work the linear unit drive must be shut down and secured against being restarted. • All installed ball bearings are sealed and maintenance-free. • Remove excessive dust and dirt [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards)

Dateityp: application/pdf
Verlinkt bei:

element (linear guide system) and a drive element (rack-and-pinion or toothed belt drive). Depending on the design, the carriage can absorb forces and torques in all directions and is non-positively connected [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards) [...] legible (in particular the serial number) and always observed. Any damaged or illegible information signs and labels must be replaced. Accident Prevention and Environmental Protection The applicable r

Dateityp: application/pdf
Verlinkt bei:

system) and a drive element (screw or timing belt drive). Depending on its design, the carriage is able to absorb forces and moments in all directions, and is positively connected to the guidance and drive [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards) [...] legible (in particular the serial number) and always observed. Any damaged or illegible information signs and labels must be replaced. Accident Prevention and Environmental Protection The applicable r

Dateityp: application/pdf
Verlinkt bei:

roller guide), and a drive element (toothed belt drive). Depending on the design, the carriage can absorb forces and torques in all directions and is non-positively connected to the guide and drive element [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards) [...] legible (in particular the serial number) and always observed. Any damaged or illegible information signs and labels must be replaced. Accident Prevention and Environmental Protection The applicable r

Dateityp: application/pdf
Verlinkt bei:

(roller guide) and a drive element (toothed belt drive). Depending on the design, the carriage can absorb forces and torques in all directions and is non-positively connected to the guide and drive element [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards) [...] legible (in particular the serial number) and always observed. Any damaged or illegible information signs and labels must be replaced. Accident Prevention and Environmental Protection The applicable r

Dateityp: application/pdf
Verlinkt bei:

method of transport, and might cause danger possibly resulting in serious injury and damage to assets. Ü Secure the Safety Lock and clamping rod separately. Ü Secure the Safety Lock and clamping rod by suitable [...] Compliance with the safety notices and other instructions set out in this manual is essential to safe working. National acci- dent prevention regulations and occupational health and safety requirements apply in [...] manufacturer must fulfill the fol- lowing obligations: • Select and integrate the Safety Lock according to DIN EN ISO 12100:2011 and the standards and regulations applying to the specific application case. •

Dateityp: application/pdf
Verlinkt bei:

Linear Units with Rack-and-Pinion Drive K / ao / 24.10.2024 geändert: ao / 24.10.20241 Lubrication Positions Gamma 090-|120-|160-|220-|280-AZSx Lubrication of guiding carriages 1+2 and 3+4 (F). Lubrication [...] Lubrication of rack (Z). Guiding carriages 1, 3, and 5 must be lubricated individually through the three funnel grease nipples on side C, guiding carriages 2, 4, and 6 through the three funnel grease nipples [...] Lubrication of rack (Z). Guiding carriages 1, 3, and 5 must be lubricated individually through the three funnel grease nipples on side C, guiding carriages 2, 4, and 6 through the three funnel grease nipples

Dateityp: application/pdf
Verlinkt bei:

are sealed and maintenance-free. The toothed belt is also maintenance-free and must only be replaced if an excess load leads to the breakage or elongation of the elastic area. Excessive dust and contamination [...] is Febis K68 or INTERFLON fin super. Please refer here to our assembly and maintenance instructions. The relubrication interval and the relubrication amount are generally influenced by many factors (e.g [...] contamination on the toothed belt and at the cover band should be regularly removed. For ball screws, relubrication intervals depend on the pitch and the spindle diameter: KGT 12xx to 32xx after approx. 2.5 x

Dateityp: application/pdf
Verlinkt bei:

system) and a drive element (screw or timing belt drive). Depending on its design, the carriage is able to absorb forces and moments in all directions, and is positively connected to the guidance and drive [...] m/s), and for any cleaning work the linear unit drive must be shut down and secured against being restarted. • All installed ball bearings are sealed and maintenance-free. • Remove excessive dust and dirt [...] art The unit conforms to the current state of the art and applicable rules and regulations. The device complies with the EC Machinery Directive and the relevant Harmonised Standards (European standards)

Dateityp: application/pdf
Verlinkt bei: