03.2021 R ot at io n sp ee d [m in -1 ] for for Extension by 2 SA mm for every 100 mm from 6 SA Total length = Stroke + 590 Stroke w ith fe at he r k ey for for deep 8.5 deep deep 0 SA 2 SA 4 SA 6 SA Mounting [...] kgm²/m Special design: Spindle support with damping ring (from 4SA: extension of total length: 10 mm for every 2 SA) Spindle support (SA) Total length [mm] Weights SSF Basic length without stroke: 38.90 kg

Dateityp: application/pdf
Verlinkt bei:

accuracy: Idle torque: 3.20 Nm Release: 10.06.2025Page B36 Total length = Stroke Strokefor for for for for for w ith fe at he r k ey 8.5deepdeep deep deep 2 SA0 SA 4 SA 6 SA Mounting elements see page B50 [...] 45 ∙10-3 kgm²/m Special design: Spindle support with damping ring (extension of total length: 10 mm for every 2 SA) Version with double nut (“MM“)not possible. . Spindle support (SA) Total length [mm] R

Dateityp: application/pdf
Verlinkt bei:

q1, q2, qn : Stroke rate for F1, F2, Fn [%] L : Nominal service life of guide [m] C : Dynamic load rating of guide (Cdyn) [N] (see Table on pages TL11 and TL12) R : Factor for roller guide size Beta 50 [...] Delta 90: R = 0,595 (Y) und R = 0,625 (Z) F : Equivalent load [N] for guide or ball screw Fv : Pretensioning [N] (3 % of Cdyn, 5 % for roller guide (see Table on pages TL11 and TL12) LKGT : Nominal service [...] is primarily the guide values for the mechanical linear drive that are used when calculating nominal service life. The ball screw must also be taken into consideration for the drive with ball screw spindle

Dateityp: application/pdf
Verlinkt bei:

Midle = Idle torque ±30% The data given for forces and moments are the respective maximum values for the single load. The individual values must be reduced for a mixed load or the appearance of several [...] slight injury or material damage. Note Includes tips for the operation and optimal use of the machine. 1.2 Intended use The linear unit is solely intended for the purpose of manipulating, positioning, transporting [...] devices or machinery, Safe operation For the safe operation of the drive, please take into account the following documentation: • these Operating Instructions for the linear unit, in particular the Technical

Dateityp: application/pdf
Verlinkt bei:

provisions of Directive 2014/34/EU (ATEX) for equipment and protective systems intended for use in potentially explosive atmospheres. The manufacturer is solely responsible for issuing this declaration of conformity [...] Part 36: Non-electrical equipment for explosive atmospheres - Basic method and requirements 2016 EN ISO 80079-37 Explosive atmospheres – Part 37: Non-electrical equipment for explosive atmospheres - Non-electrical

Dateityp: application/pdf
Verlinkt bei:

provisions of Directive 2014/34/EU (ATEX) for equipment and protective systems intended for use in potentially explosive atmospheres. The manufacturer is solely responsible for issuing this declaration of conformity [...] Part 36: Non-electrical equipment for explosive atmospheres - Basic method and requirements 2016 EN ISO 80079-37 Explosive atmospheres – Part 37: Non-electrical equipment for explosive atmospheres - Non-electrical

Dateityp: application/pdf
Verlinkt bei:

-502 Lubricating greases for extreme requirements Klüberplex BE 31-102…-222…-502,Prod. 017135, 017132, 017126,en Edition 20.01.2020 [replaces edition 20.01.2020] Benefits for your application – Longer [...] 31-102…-222…-502 are lubricating greases for e.g. rolling and plain bearings, pivoting bearings, small gears. They can also be used as sealing and lubricating greases for labyrinth seals and industrial valves [...] by grease guns, brush or spatula. For application via central lubrication systems, please check pumpability with the manufacturer. Commercial detergents can be used for pre- cleaning the friction points

Dateityp: application/pdf
Verlinkt bei:

Midle = Idle torque ±30% The data given for forces and moments are the respective maximum values for the single load. The individual values must be reduced for a mixed load or the appearance of several [...] slight injury or material damage. Note Includes tips for the operation and optimal use of the machine. 1.2 Intended use The linear unit is solely intended for the purpose of manipulating, positioning, transporting [...] devices or machinery, Safe operation For the safe operation of the drive, please take into account the following documentation: • these Operating Instructions for the linear unit, in particular the Technical

Dateityp: application/pdf
Verlinkt bei:

DynaGear series are components for installation in machines and intended exclusively for guiding, distributing and multiplying torques. DynaGear have been designed only for the operational use described [...] accept any liability for any resulting damage and faults. 2. Intended use of MS-Graessner gear units DynaGear gear units are components for machine installation and intended exclusively for guiding, distributing [...] kept in a safe place for later consultation. It comprises important notes on the operation and service of the DynaGear series of gear units. These operating instructions are intended for all persons carrying

Dateityp: application/pdf
Verlinkt bei:

fe at he r k ey de ep 15 de ep Total length = Stroke 12deep Outlet for internal screw holes for short strokes Forces and moments * for KGT 3240: 8000 N Stroke / 42 = Number of pleats Number of pleats ∙ [...] of block length of bellows (FB) Example for stroke of 500 mm: 500 mm / 42 = 11.90 => 12 pleats (rounded up) 12 ∙ 3 – 2 = 34 mm simple block length (FB) * For KGT 3240: 8000 N R ot at io n sp ee d [m in

Dateityp: application/pdf
Verlinkt bei: