its efficiency. 1.2 Regulation use The mechanical linear unit is intended for installation in machines, and is used solely for manipulating, positioning, transporting, palletising, loading, unloading, [...] industrial environments. Any other use, or use for purposes beyond those stipulated, will be classed as illegitimate. The manufacturers accept no liability for any loss thereby incurred. The risk is borne [...] operation, refer to the following documents: • This operating manual for the linear unit, particularly the technical data • The operating manual for the line into which it is installed Decommissioning Dispose of

Dateityp: application/pdf
Verlinkt bei:

and the bearing type. For mechanical linear units, the free spindle length can be changed by installing spindle supports. An approximate calculation of the critical revolution for HSB linear units can be [...] (fixed/movable bearings) were used to calculate the number of spindle supports (see SA diagrams). For vertical installation with the fixed bearing at the bottom, the additional buckling must be taken into

Dateityp: application/pdf
Verlinkt bei:

its efficiency. 1.2 Regulation use The mechanical linear unit is intended for installation in machines, and is used solely for manipulating, positioning, transporting, palletising , loading, unloading [...] industrial environments. Any other use, or use for purposes beyond those stipulated, will be classed as illegitimate. The manufacturers accept no liability for any loss thereby incurred. The risk is borne [...] operation, refer to the following documents: • This operating manual for the linear unit, particularly the technical data • The operating manual for the line into which it is installed Decommissioning Dispose of

Dateityp: application/pdf
Verlinkt bei:

its efficiency. 1.2 Regulation use The mechanical linear unit is intended for installation in machines, and is used solely for manipulating, positioning, transporting, palletising , loading, unloading [...] industrial environments. Any other use, or use for purposes beyond those stipulated, will be classed as illegitimate. The manufacturers accept no liability for any loss thereby incurred. The risk is borne [...] operation, refer to the following documents: • This operating manual for the linear unit, particularly the technical data • The operating manual for the line into which it is installed Decommissioning Dispose of

Dateityp: application/pdf
Verlinkt bei:

standard EN 61000-6-1. Any other use, or use for purposes beyond those stipulated, will be classed as illegitimate. The manufacturers accept no liability for any loss thereby incurred. The risk is borne [...] operation, refer to the following documents: • This operating manual for the linear unit, particularly the technical data • The operating manual for the line into which it is installed Decommissioning Dispose of [...] relubricated with a grease suitable for use in clean rooms (basic lubrication carried out using Klübersynth BEM 32-34). 1.5 Use in explosive areas The linear units are suitable for use in explosive atmospheres

Dateityp: application/pdf
Verlinkt bei:

fitness for a particular purpose or course of performance or usage of trade.The company is not responsible for damages caused by the use ofthe product in applications for which it was notintended or for conditions [...] followed.EYE Immediately Flush eyes with large amounts ofwater for at least 15 minutes. SKIN Wash skin with water and soap. INGESTION No need for first aid is anticipated. If person is conscious, flush mouth [...] cited in European regulation for protection of men and Environment DPR 303/56 (General regulation forsafety and hygiene in work pIaces) . 16TH SECTION -OTHER INFORMATION For other information call the phone

Dateityp: application/pdf
Verlinkt bei:

employ a suitable motor with a restraining brake. Efficiency For trapezoidal screws, the mechanical efficiency is generally below 50 %; for ball screws however it is up to 98 %. Ball screws permissible [...] Temperatures All ball screws are designed for ambient temperatures from 0 °C to 80 °C. Temperatures of a minimum of -20 °C and maximum of 110 °C are also permissible for brief periods. Ball screws are subject [...] ball contact angle is 45° (±5°). Speeds The generally permitted speed limit is 3000 rpm. On request, for certain sizes and installation situations, speeds up to 4500 rpm are permissible. The speed limits

Dateityp: application/pdf
Verlinkt bei:

respect for human dignity, openness and non- discrimination on grounds of religion, ideology, gender or ethnicity. For our company, organisational governance means a legal and regulatory framework for the [...] protection, for example) are given special attention in our organisation. $4 Complaints mechanism In order to uphold human rights at all operational levels in our organisation, as well as for all stakeholder [...] suppliers and owners, as well as our social environment worldwide (“stakeholders”). We undertake to call for, monitor, promote and continuously improve compliance with this CoC by all stakeholders to the best

Dateityp: application/pdf
Verlinkt bei:

on side D. The rack must be lubricated through the funnel grease nipple on side B (for models BXD/BXC) or on side A (for models ALD/ALC). F(1) F(4) F(2) F(3) Z Z F(1) F(3) F(5) Gamma 090-|120-|160-GDHE (fixed [...] Lubrication Points for Gamma Linear Units with Rack-and-Pinion Drive K / ao / 24.10.2024 geändert: ao / 24.10.20241 Lubrication Positions Gamma 090-|120-|160-|220-|280-AZSx Lubrication of guiding carriages [...] be lubricated through the funnel grease nipple on side B. Z F(3) F(1) F(5) F(7) Lubrication Points for Gamma Linear Units with Rack-and-Pinion Drive K / ao / 24.10.2024 geändert: ao / 24.10.20242 Gamma

Dateityp: application/pdf
Verlinkt bei:

accuracy 23 µm/300 mm [T5] or similar) * For single nuts without spindle (KGM-M, KGM-F) only standard play is available. Page K9 Release: 24.04.2017 Ordering code for ball screw [...] K6 continue following) X = separated G = annealed K = to customer‘s drawing Length of spindle end for fixed bearing Total length spindle Spindle end floating bearing A, B, C = standard end (page K6 continue [...] continue following) X = separated G = annealed K = to customer‘s drawing Length of spindle end for floating bearing Play / pre-load * S2 = standard play pitch 5 mm and 10 mm approx. 0.04 to 0.06 mm pitch

Dateityp: application/pdf
Verlinkt bei: